Ghost Controls Access Control Installation Nationwide

Ghost Controls Access Control Installation: The Boca Raton Owner’s Guide

We install Ghost Controls access control systems in Boca Raton daily, and a full keypad, intercom, or receiver installation typically runs between $380 and $750, including the part and labor. Most jobs are completed in a single visit, and if the part is on our truck, which it usually is for Ghost Controls, we can often be on site the same day you call. The way homeowners usually discover a failed access control installation is simple: the keypad stops responding, the remote works but the keypad doesn’t, or the gate opens on its own at 2 a.m. because the receiver board is picking up phantom signals. If you’re standing at the keypad with the gate ignoring you, here’s what’s actually happening and what it costs to fix.

Call (754) 666-7602

Key Takeaways:

• Ghost Controls access control installation in Boca Raton runs $380-$750 installed, written before work starts
• We stock Ghost Controls keypads, receivers, and control boards on our trucks
• Boca Raton’s humidity and salt air shorten access control component life by roughly 20-30% compared to inland Florida
• Every install includes a photo log of connections, dip switch settings, and the final programmed state

Which Ghost Controls Models This Applies To

Ghost Controls access control components are designed to work with their AXDP and AXD series gate openers: the AXD, AXDP, AXD-M, and AXDW dual-gate kits, as well as the newer GHO series. The keypad model you’ll see most often on Boca Raton gates is the GHPK1, the wireless keypad that pairs with the AXDP control board. If you’re adding a hardwired keypad, the GHWK1 or a compatible linear-style keypad wired into the control board’s accessory terminals is the route. Either way, the first thing we check is the control board revision stamped on the circuit board itself, because Ghost Controls changed their accessory terminal layout between the AXD and AXD-M generations, and a keypad wired to the wrong terminal block will never respond, no matter how many times you re-enter the code.

OEM Ghost Controls keypads run $110 to $180 for the part alone. There are quality aftermarket keypads that work, but we’ve seen too many Boca Raton installs where a generic keypad paired fine for six months and then lost programming after a power blip. For Ghost Controls specifically, we recommend OEM receivers and keypads, because the pairing protocol is proprietary and the aftermarket compatibility lists are optimistic at best. We are an independent service provider, not affiliated with Ghost Controls, but we stock their parts because we see more of their openers on Palm Beach County gates than any other brand except LiftMaster and Mighty Mule. Those two plus DoorKing are the other brands we keep keypads and receivers for on the truck.

Signs Your Ghost Controls Access Control Installation Is Failing

• The keypad beeps but the gate won’t move. The keypad is transmitting, but the receiver on the control board isn’t decoding the signal. In Boca Raton, this is often corrosion on the receiver board from humidity, or the keypad and board lost their paired memory after a power outage.
• Random gate openings at odd hours. A failing receiver board can start reading stray radio signals from nearby gate systems or even weather station frequencies. If your gate opens on its own, unplug the keypad receiver and see if the behavior stops. That’s a board replacement, not a ghost.
• Keypad works only from five feet away or less. The keypad’s internal antenna or battery is degrading. A fresh battery sometimes fixes it. If not, the keypad’s transmit strength has dropped, and reprogramming won’t restore range.
• The keypad is cracked, fogged, or water inside the lens cap. Boca Raton’s wet season and salt air get inside these keypads through hairline cracks and failed gaskets. When the circuit board sees moisture, buttons start double-firing, and the keypad is done.
• The gate opens from the remote but never from the access panel. If every handheld remote works but the keypad doesn’t, the keypad’s code memory has likely been wiped or the pairing was lost entirely. This is a reprogramming job at minimum, a keypad replacement if the board shows corrosion.

One Boca Raton-specific note: we regularly see keypads mounted in full afternoon sun, and the UV breaks down the silicone membrane behind the buttons. The keypad still clicks, but the membrane no longer closes the circuit. It looks fine and fails completely. That’s why we check the dome and membrane before we ever quote a board replacement.

Before

After

Replacement Cost & What’s Included

In Boca Raton, a Ghost Controls access control installation, meaning a new keypad, receiver, or control board installed and programmed, lands between $380 and $750. The low end covers a wireless keypad paired to an existing board with no other faults. The high end covers a receiver board plus a hardwired keypad, including running and concealing the low-voltage wire from the gate post to the keypad location.

We price this work in writing before anything is touched. The quote shows the part number, the part price, the labor time, and the total, handed to you before the first screw comes out. That’s just how we work. The installation includes the part, the programming of all codes and dip switches, the weatherproofing of every connection with dielectric grease and heat-shrink, and a full photo log of the finished work: the board wiring, the keypad mounting, the limit settings, and the programmer’s screen showing the code count. The labor carries our 365-Day Done Right Promise. If the access control install fails within a year, we return and make it right at no charge.

What drives the price within that range is simple: wireless keypads are cheaper and faster to install. Hardwired keypads cost more because the low-voltage wire has to be run, usually under a paver walkway or through a gate post. And any time we’re replacing a receiver board on an older AXD series, we quote a board plus keypad because the original keypads are usually at the end of their life too.

DIY or Call Us?

You can safely do the simple tests: check the battery, look for water inside the keypad, and confirm the gate opens normally with the remote. If the keypad is physically cracked or the board shows white corrosion powder, stop there. Access control runs on 12-volt low voltage, so the electrical hazard is minimal, but the programming hazard is real. If you wire a keypad to the wrong terminal on the control board, you can damage the board itself, and a Ghost Controls AXDP board is a $240 part before labor. The dip switch and code programming is also easy to get wrong, and every wrong setting compounds the troubleshooting time. If the battery test doesn’t fix it, call us at (754) 666-7602 and we’ll diagnose it on site with the meter and the manual. The fixed price is written before we begin.

FAQs