Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Hinge & Roller Replacement: The Boca Raton Owner’s Guide
FAAC hinge and roller replacement in Boca Raton typically runs $280 to $520 installed, including the parts and the labor to align the gate properly afterward. We stock FAAC-compatible hinge and roller kits on the truck for the most common residential swing and slide gate series, so most replacements are same-day when the gate is a standard configuration. What you’ll usually notice before you call: the gate drags at one end, the leaf sits noticeably lower than it did last month, or you hear a grinding sound near the hinge post when the gate moves. The roller wears down or the hinge bearing wallows out, and then the whole gate starts working against itself.
Which FAAC Models This Applies To
Most FAAC residential swing gates in Boca Raton use one of three hinge configurations: the S800 series (commonly paired with FAAC 391 and 400 operators), the 750/760 series, and the older 402/412 setups. Slide gates use a cantilever roller system or a V-track roller assembly depending on the installation. The hinge itself will have a stamped number on the barrel or the mounting plate. If the stamp is gone, we measure the leaf thickness match to the hinge opening and the pin diameter, because a hinge that doesn’t fit the leaf depth will fail again within a season.
One compatibility gotcha we see regularly: FAAC’s newer hinge kits changed the mounting bolt spread by about 8 millimeters compared to the mid-2000s units. A homeowner’s “identical” hinge from a parts site shows up and doesn’t line up with the existing bolt holes, and then they’re drilling the gate frame in the Florida heat or paying us to correct it. We carry both OEM FAAC parts and quality aftermarket equivalents from door-hardware manufacturers that meet the same load ratings. For safety-critical hinge assemblies, we prefer OEM FAAC or a direct-spec aftermarket part with the same pin diameter and plate thickness. We’re an independent service provider, not affiliated with FAAC.
Signs Your FAAC Hinge & Roller Replacement Is Failing
- Gate leaf sag at the latch end. The gate drops enough that the latch doesn’t line up or the leaf drags on the driveway. A worn hinge pin or a wallowed hinge barrel allows the leaf to tilt, and the geometry only gets worse as the operator pushes against the misalignment.
- Grinding or squealing from the hinge post area. Roller bearings lose their grease seals in Boca Raton’s humidity and salt air, then the rollers run dry. You hear metal-on-metal contact before you see visible wear, because the roller is inside the track or the hinge barrel.
- Stuttering or jerky gate movement. The motor is fighting resistance from a binding hinge or a flat-spotted roller. The limit switch then trips early or late, which makes the gate stop short or overshoot.
- Visible wear grooves on the track. A flat-spotted roller carves a groove into the track over months. By the time the groove is visible, the roller has been failing for a while and the track may need attention too.
- Gate sits lower on one side after the wind blows. Boca Raton afternoon storms put lateral load on the hinge pins. A hinge with worn pin clearance lets the gate settle out of level after a hard blow.
BeforeAfterReplacement Cost & What’s Included
The installed cost for FAAC hinge and roller replacement in Boca Raton breaks down like this:
- Hinge replacement (standard swing gate, single leaf): $180-$320 installed, depending on hinge spec and whether the mounting plate has corrosion to address.
- Roller replacement (V-track or cantilever slide gate): $140-$280 installed, including track inspection and re-alignment.
- Hinge and roller package on a double-leaf gate: $380-$620 installed, which covers both leaves and the matching hardware set.
Every job includes the written price before we touch the gate, the new part number documented on your receipt, and a photo log of the installation. The work is covered by our 365-Day Done Right Promise: if something isn’t right within a year, we make it right at no additional charge. No surprises on the invoice. Ever.
DIY or Call Us?
What you can safely do: photograph the part, measure the pin diameter and the bolt spacing, and check the gate leaf for visible sag or track grooves. That saves time on the phone and helps us bring the right part on the first trip.
What we don’t recommend: pulling the hinge pins on a loaded gate yourself. A swing gate leaf weighs 300 to 700 pounds depending on size and material, and when that last pin comes out, the leaf wants to turn its own weight against you. Same for slide-gate rollers: if the gate sits on its rollers, removing one shifts the load onto whatever else is under the gate, including your hands if you’re in the wrong spot. We use a gantry or a jack to take the weight off before we touch the pins. That’s not a homeowner tool kit situation. If your FAAC hinge or roller is gone, call us at (754) 666-7602 and we’ll get it handled safely.
FAQs
Five to nine years is typical for FAAC hinges and rollers in coastal South Florida, depending on the part’s exposure. Salt air and summer humidity are harder on the hardware than the motor in most installations. Hinges closer to the ocean or within a mile of the Intracoastal tend to wear faster because the protective coatings break down sooner. If your gate is within a couple miles of the water, expect the lower end of that range.
Usually not, because the failure is mechanical wear: the pin clearance is gone, or the bearing surface is wallowed. You can buy temporary time by greasing the pin, but re-sleeving a hinge barrel costs more in labor than a quality replacement hinge. We’ll tell you straight if a repair is viable, but most hinge failures we see in Boca Raton are replacement jobs. Call (754) 666-7602 for an honest assessment.
Most single-leaf hinge replacements or roller swaps take 60 to 90 minutes on site. A double-leaf gate with both hinges and rollers runs two to three hours, including re-aligning the operator limit switches after the gate geometry changes. We schedule the work so the gate is operational the same day except in cases where the track itself needs replacement, which we’ll flag before we start.
Yes. We stock the FAAC 750/760 and S800 hinge kits, plus V-track and cantilever roller assemblies for the most common FAAC slide gate series in the Boca Raton area. We also keep parts for LiftMaster, Mighty Mule, and Ghost Controls gates. If your part isn’t on the truck, we’ll give you the exact price and the lead time before you commit to anything.
Written by Adrian Vance, Owner, Vance Gate Repair Boca Raton at Vance Gate Repair Boca Raton, serving Boca Raton and nearby areas.