Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Parts & Welding for Boca Raton Homeowners
A sagging gate in Boca Raton is rarely a mystery once you look at the hardware. The hinge has wallowed out, the post has shifted in sandy soil, or a weld has finally let go after ten years of salt air. Our Gate Parts & Welding in Boca Raton fixes the gate you already have, instead of replacing it. Most hinge replacements, roller swaps, and latch repairs run between $180 and $650 in Boca Raton, and we can usually be on-site the same day you call. Adrian Vance founded Vance Gate Repair in 2014 doing commercial access-control work, where documenting every limit-switch reading was standard practice. We brought that habit to residential gates. Every job gets a written price before work starts and a photo record when we leave. Call (754) 666-7602 and you’ll speak to a live person, any hour, any day.
What Our Gate Parts & Welding Service Includes
Hinge Replacement
Gate hinges carry the full weight of the gate, and in Boca Raton’s coastal air they corrode from the outside while wearing from the inside. When a gate starts dragging on the ground or the top corner leans out from the post, the hinge pins or barrels are usually done. We cut off the old hinges, weld or bolt new ones in place depending on the gate frame, and set the gate so it swings level without binding. We photograph the old hinge before removal and the new one after installation, so you can see exactly what was replaced. Ball-bearing hinges on heavier gates get greased and tested through a full open-close cycle before we call the job finished.
Post Replacement
A gate post that’s leaning more than a few degrees cannot be straightened by adjusting the gate. The post itself has failed, usually because the original installer set it in a shallow hole or the concrete pad has cracked. In Boca Raton, sandy soil and heavy summer rains accelerate post settling, especially for driveway gates with a lot of swing weight. We remove the old post, dig a proper footing, set a new steel post in concrete, and brace it while it cures. Then we remount the gate, reset the hinges, and confirm the gate swings true before we pack up. You get a written record of the post depth and concrete volume, because the next technician should never have to guess what’s underground.
Rail Repair
Slide gates run on a rail, and a bent or pitted rail turns every open and close into a grinding, lurching fight. The motor works harder, the rollers flat-spot, and eventually the gate stalls mid-travel. We inspect the full rail run for bends, weld fractures, and low spots, then splice or replace damaged sections as needed. Where the rail has sunk because the base has washed out, we re-level the base and shim it before re-securing the rail. We set the end stops and re-check the limit switches after the rail work is done, because a repaired rail with a mis-set limit will just crash into the post. The photo log shows the rail condition before and after, in sections.
Custom Welding
Not every gate repair is a stock part. Cracked frames, broken pickets, missing brackets, or a gate that needs to be extended a few inches to close a gap all call for custom welding. Our welders work in steel and aluminum, on-site, with portable MIG and TIG setups. We fabricate brackets, patch rusted-through sections, and rebuild corners that have cracked at the weld joint. Every weld gets ground smooth, primed, and painted to match the surrounding metal as closely as possible. We photograph the fracture, the weld after grinding, and the finished painted section. If the gate is aluminum, we match the filler rod to the base alloy so the weld doesn’t fail from galvanic corrosion.
Gate Rollers
Rollers are the most common failure point on slide gates in Boca Raton. The bearings seize, the wheel develops a flat spot, and the gate starts shuddering through its travel. We stock replacement rollers in steel, nylon, and polyurethane for most slide gate tracks, and we can machine or order uncommon sizes. We replace rollers in pairs so the gate doesn’t run cocked on one good wheel, then adjust the guide rollers so the gate tracks straight without side-to-side play. The old rollers get photographed next to the new ones on the job record, and we note the bearing type installed. A gate that rolls quietly and without vibration is the standard, not a bonus.
Latch & Lock
A gate that won’t stay closed is a gate that isn’t doing its job, and in Boca Raton a gate left swinging is an invitation to a pool-area liability you don’t want. We rebuild and replace mechanical latches, install and key gate locks, and convert old manual latches to magnetic or solenoid locks where the gate already has an opener. Misaligned latch plates get repositioned and welded or bolted so the latch catches cleanly on the first try. We test the latch from both sides, with the gate opening inward and outward if the hinges allow it. The job record includes the lock brand, the key code or cylinder type, and a photo of the striker alignment before and after.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Parts & Welding
We work on FAAC gates constantly across Boca Raton, and the parts-side work on those units is usually straightforward: hinge plates, latch brackets, and rail sections that match the original FAAC geometry. We keep FAAC-compatible replacement rollers and stop plates on the truck, and when a FAAC gate needs a weld repair, we match the metal thickness so the repair doesn’t change the gate’s balance. FAAC’s swing arms put specific stress on the hinge line, so we inspect the full hinge path before we weld anything.
BFT and Linear both appear regularly on Boca Raton driveways, especially on newer construction, and Deerfield Beach Gate Parts & Welding is available nearby if you’re just north of us. BFT gates tend to be aluminum, which means our welders adjust the welding process to avoid burn-through on thinner sections. Linear gates show up on slide applications, where the rail and roller wear patterns are predictable. Viking operators don’t come through as often, but when they do, the parts we replace are usually mechanical rather than electronic: worn rollers, cracked brackets, and sagging gate frames. Whether you have one of those brands or any other make, the parts and welding work doesn’t depend on the motor brand. The gate itself is steel or aluminum, and we repair it either way.
BeforeAfterSigns You Need Gate Parts & Welding Right Now
- The gate drags or scrapes on the ground. A dragging gate is either a failed hinge, a bent post, or a wheel that has gone flat. Each one gets worse with every open-close cycle, and the motor is taking the strain. Getting it fixed now usually saves the motor.
- The gate shudders or bounces while moving. Vibration through the gate means the rollers are flat-spotted or the rail has a low spot. The motor is fighting an uneven load, and limit switches start to read incorrectly. A smooth-rolling gate is a quieter gate and a cheaper gate to keep.
- The gate leans toward the latch or away from the post. A visible lean means the post or hinge structure is failing, not the gate panel itself. Ignoring the lean wears out the latch, the hinges, and eventually the motor. Leveling the post before it fails completely is a smaller job than replacing a dropped gate.
- The latch won’t catch, or you have to lift the gate to close it. When the latch plate and the striker don’t line up, either the hinges have sagged or the post has moved. Forcing the latch closed stresses the frame and eventually cracks a weld. Aligning the latch is often a same-day fix.
- You see cracks or rust-through on the gate frame. A crack at a weld joint is a stress failure, and it will keep propagating until the gate has to be re-fabricated. Catching a crack early means a short weld repair instead of a gate replacement. Rust-through near the hinges is the same story in Boca Raton’s salt air.
Our Gate Parts & Welding Process - Step by Step
- 1
On-site inspection and written diagnosis. We arrive, measure the gate, check the hinges, rollers, posts, and welds, and tell you exactly what we found in plain terms. The diagnosis is written down and priced before any work starts. No toolbox opens until you’ve seen the number.
- 2
Written scope and written price. The scope lists each part we’ll replace, each weld we’ll make, and the labor involved. That’s Haven Standard Clause 1: have it in writing. The price you see is the price you pay, period. If we find something else during the work, we stop and show you before adding a dollar.
- 3
Parts removal and surface prep. We cut, unbolt, or disassemble the failed parts and prep the surfaces for new hardware or weld. For welding, we grind to clean metal at the joint, set the gate square and level, and clamp it in position. The prep is what determines whether a weld holds for a season or for a decade.
- 4
Installation or welding, then testing. New hinges get set, rollers get paired up, posts get set in concrete, welds get ground and primed and painted. Then we run the gate through a full open-close cycle multiple times, check every bolt for torque, and verify the gate sits level and swings or slides smoothly.
- 5
Photo documentation and owner walkthrough. Before we leave, you get a documented photo record: what we found, what we removed, what we installed, and the final result. Every adjustment and part number is written on the job record and left with you. Clause 4, evidence on every job, at no additional charge.
How Much Does Gate Parts & Welding Cost in Boca Raton?
If you’re wondering how much Gate Parts & Welding costs, it depends on which part failed and how far the damage has spread. A typical hinge replacement runs $180 to $450 per hinge depending on the gate’s weight and the hinge grade, and most residential gates have two or three hinges. A post replacement runs $500 to $1,200 when the post is steel and set in a proper concrete footing. Roller replacement for slide gates usually lands between $150 and $350 per pair. Custom welding is quoted by the inch of weld and the prep involved, but most residential weld repairs run $250 to $800. The main factors that move the price are metal thickness, post depth, and whether the gate has to be removed and re-hung to make the repair safe.
The best way to avoid overpaying is to get a written scope instead of a verbal estimate. A quote that says “repair gate” tells you nothing. A scope that says “replace two ball-bearing hinges, weld one cracked picket, re-align latch plate” tells you exactly what you’re buying. Our estimates are free, they’re written, and they hold. If you have a written estimate from another company, bring it to us for a free second opinion. We’ll walk through it line by line and tell you what’s necessary and what isn’t. Under no circumstances do we start work on a parts and welding job without a written price in your hand first.
Gate Parts & Welding Near Boca Raton - Our Service Area
We handle gate parts and welding across Boca Raton and the surrounding areas, including Deerfield Beach, Delray Beach, Lighthouse Point, Coconut Creek, Pompano Beach, Parkland, Margate, Boynton Beach, Coral Springs, Lauderdale-by-the-Sea, and North Lauderdale. Most calls in Boca Raton proper get a same-day response, and the surrounding cities are usually next-day. If you’re in Deerfield Beach with a sagging gate, check our Gate Parts & Welding in Deerfield Beach page for local details, or see Gate Parts & Welding in Delray Beach if you’re further south. We also provide full home gate repair services across the whole area.
Serving Boca Raton, FL - Our Local Coverage Area
We’re based in the Boca Raton area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Parts & Welding in Boca Raton
Gate parts and welding is the mechanical repair of the gate itself, as opposed to the motor or opener. It includes replacing hinges, rollers, latches, and posts, plus welding cracked frames, broken brackets, and rusted-through sections. We do the work on-site in Boca Raton rather than hauling your gate to a fabrication shop. The goal is to make the gate structurally sound again so the opener doesn’t have to fight a failing frame.
Most hinge replacements, roller swaps, and latch repairs are done the same day, typically in one to three hours on-site. A post replacement takes longer because the concrete has to cure before the gate is re-hung, usually one day of work and another day of curing. Custom welding jobs vary by the amount of repair, but most residential welding is completed in a single visit. We’ll tell you the expected timeline in writing before we start.
Gate Parts & Welding - Delray Beach and Boca Raton typically runs between $180 and $650 for the most common repairs: hinges, rollers, latches, and small welds. Post replacement and larger fabrication jobs can run $500 to $1,200 or more depending on scope. You’ll get a written price before any work begins, not a range that drifts upward later. Call (754) 666-7602 for an exact quote on your specific gate, free of charge.
Yes, we service FAAC gates regularly across Boca Raton, including parts replacement and welding on FAAC-compatible gate frames. The same goes for BFT, Linear, and Viking, among other brands. The parts and welding side of the repair is about the metal and the mechanics, not the motor brand. We work on whatever gate you have, with no push toward replacement.
We keep same-day availability for gate repairs in Boca Raton whenever possible, and a live person answers our phone 24 hours a day. Call (754) 666-7602 and we’ll tell you straight whether a technician can be there today. The written price still applies on emergency work. You’ll know the cost before the first tool comes off the truck.
Every parts and welding job we complete is covered by our 365-Day Done Right Promise. If the repair is not right within one year, we make it right at no additional charge, no argument. That covers the welds, the hardware, and the labor we performed. It does not cover damage from impact or conditions unrelated to the original repair.
Clear the area around the gate so we have room to work, and make sure the gate is in the closed position if possible. Move any vehicles that block the swing or slide path. If you have pets that use the yard, keep them inside during the visit. We’ll handle the rest, including the written scope and the documentation.
Schedule Your Gate Parts & Welding Service in Boca Raton Today
Get a live person, a written price, and a documented photo record on every visit. That’s the Vance Gate Repair standard, and it applies to every hinge, post, roller, and weld we touch in Boca Raton. Call (754) 666-7602 for a free, no-obligation estimate. We’re available 24/7, and the price you see in writing is the price you’ll pay.
Written by Adrian Vance, Owner at Vance Gate Repair, serving Boca Raton since 2014.